Used ROSS model RVMS-100, 100 Gallon / 380 Liter Pharmaceutical mixing reactor. Rated 30 PSI @ 300 Deg.F. Has "Egg Beater" and turbine blade on one mixing shaft. Mixer drive is Lightnin 1.74 HP, 208-220/440 volt, 1725/1425 RPM. Has lift to raise mixer and lid.

Used 120 Cu Ft Nauta Mixer. Mfg Ross. 304 Sanitary Stainless Steel Construction. 2HP Orbit Arm. 7.5HP screw drives. Dome top with 24" manway, 4" top nozzle, 8" discharge. Controls. Serial #66256. Built 1995.

Used 15 gallon Ross dual shaft mixer. Model CDA 15. Stainless steel construction. Anchor agitator driven by 3 hp, 230/460 volt motor. High speed disperser driven by 10 hp, 230/460 volt motor. Vacuum cover, approximately 16.75" diameter x 20" deep jacketed mixing can. Bottom outlet with ball valve. Air over oil hydraulic lift with air tank. Control panel with motor vfd controllers. Floor mounted. Serial# 71551.

Used 300 Gallon ROSS Model CDA-300 Dual Shaft Vacuum Mixer with Sweep and High Shear Disperser Mixers. Unit equipped with Portable Jacketed Tank rated 2 PSI / FV @ 300F. Jackets rated 50 PSI @ 300F. 20HP anchor sweep motor and 60HP disperser motor. Serial #108627-20.

Used 10 gallon 304L Stainless Steel Triple Shaft Mixer. Manufactured by Ross. Model PVM-10. Jacketed mix can rated 125PSI/FV. Variable speed Triple Shafts 5HP disperser, 3HP anchor agitator and 1.5HP emulsifier. 480V/60Hz/3 Phase, 30 Amp. Air over Oil lift with air tank. Serial #50865. Built 1987.

Used 32 Cu Ft Ross Nauta Mixer. 68" diameter upper cone diameter x 91" overall cone height. 12" diameter agitation screw driven by 5 horsepower motor 230/460/3 and gear reducer by sew eurodrive @ 58 rpm, 1.5 horsepower orbitial arm drive with sew eurodrive motor 230/460/3 and gear reducer operating at 1.5 RPM. Liquid spray nozzle, bottom delumper, bottom discharge with manually operated 12" slide gate valve. voltage, central painted steel bridge with mounted drive motors, 2/3 SS bolt on cover with 1/3 hinged cover, mounts from four equally spaced gusseted mounting pads. Serial #6771.

USED ROSS MODEL V-10 10 CUBIC FOOT STAINLESS STEEL SCREW TYPE BLENDER. WEATHERED PARTS MANUFACTURED OF 304 STAINLESS STEEL. UNIT IS DESIGNED FOR FULL VACUUM OPERATION. UNIT HAS 3 HP AND 1 HP DRIVES. MANUFACTURED 6/1987. VESSEL MEASURES 52" DIA X 65" STRAIGHT SIDE. 10" DOME INSPECTION COVER ON LID. 2 1/2" AND 4" FEED PORTS. UNIT HAS MOUNTING PADS BUT NO LEGS. SERIAL #51722.

Used Ross Series 400 In-Line Mixer, Model HSM 401SC2, 316 Stainless Steel. Rated 66 gallon per minute (water). Non-jacketed chamber approximately 3-1/2" diameter x 2-1/2" deep, rotor approximately 3-7/16" diameter, slotted stator approximately 2-1/2" diameter. 1-1/2" Tri-clamp inlet/outlet. Driven by 2 HP, 3/60/200/240 volt, 3425 rpm stainless steel wash down motor. Include mechanical seal with lubricator, and an AC Tech MC Series intelligent drive. Mounted on a stainless steel base with casters. Serial number 105517.

Used Ross HSM-110 mixer. Serial #109614.